Help

Build guides

Make your own impulse response

Record a room, a cabinet or an object as an impulse response with a sine sweep or a click, or design one, then prepare a WAV file a Maru convolution effect can use.

You can make an impulse response (IR) of almost anything that sound passes through: a room, a stairwell, a guitar cabinet, a metal bowl. You play a known sound through it, record what comes back, and turn that recording into the space's answer to a single click. The result is an ordinary WAV file. This guide covers the three ways to make one and how to prepare the file so a Maru convolution effect accepts it.

MethodQualityWhat you needGood for
Sine sweepBest: clean, full range, low noiseA speaker, a microphone, an audio interface and a measurement toolRooms, halls, cabinets you want to ship
Click or popRough: noisy, uneven bassA microphone and something that makes a sharp, loud clickQuick captures and creative character
DesignExactly what you specify, no noiseCode or any audio editorEffects you can adjust and ship without licensing anyone's recording

Capture a space with a sine sweep

A sweep is a sine tone that glides from the lowest to the highest frequency. Because the tone covers each frequency in turn, a measurement tool can divide the recording by the sweep and recover the impulse response, with far less noise than a click gives. Free tools such as Room EQ Wizard (REW), and the impulse-response utilities some DAWs include, generate the sweep and do this step for you.

  1. Make the sweep. Use an exponential (logarithmic) sweep from 20 Hz to 20 kHz, 5 to 15 seconds long. Longer sweeps reject more background noise. Follow it with silence at least as long as the space rings: a few hundred milliseconds for a cabinet, two or three seconds for a room, six or more for a large hall.
  2. Place the speaker and the microphone. Put the speaker where the sound source would be (a singer, a drum kit) and the microphone where the listener would be. The distance between them is part of the sound. For stereo, record two microphones at once, spaced or crossed.
  3. Set the level. Play the sweep loud enough to stand well above the room's noise, with the recording peaking around −12 to −6 dBFS. Turn off fans, fridges and air conditioning, and keep still while it records.
  4. Record. Use the sample rate you will use the IR at (48 kHz is a good default) and 24-bit or 32-bit float. Record the sweep and all of the silence after it.
  5. Recover the IR. Give the tool the recording and the original sweep. It returns the impulse response. Record two or three takes and keep the cleanest one.

An exponential sweep has a useful side effect: distortion from the speaker lands before the impulse response in time, separate from it. Trimming the start of the file, described below, removes it.

True stereo. A stereo IR records one speaker position. To capture how a room answers sound from both sides, measure twice, with the speaker on the left and then on the right, keeping the two microphones in place. The four recovered channels, in the order left→left, left→right, right→left, right→right, make a four-channel true-stereo IR.

Cabinets. Feed the sweep through a power amplifier into the cabinet (never through the guitar amplifier's own distortion) and place the microphone close to the speaker, as you would to record a guitar. Moving the microphone across the cone changes the tone more than anything else. A cabinet IR only needs the first 20 to 200 milliseconds.

Capture a space with a click

A balloon pop, a hand clap, a starter pistol or two pieces of wood slapped together all make a short burst that excites a space. Record it with the microphone where the listener would be, and the recording is already an impulse response: there is nothing to recover.

The catch is that a click is not equally loud at every frequency. Bass is usually weak, the click itself colours the result, and background noise is much louder relative to the tail. Use clicks for a quick capture of a space you can't bring a speaker to, or when that character is what you want.

Design an impulse response

An IR does not have to be a recording. A short burst of noise that fades out smoothly already sounds like a room; filtering it darker over time sounds like a room with soft furnishings; a few sharp, spaced peaks at the start sound like walls. Space Mini builds all of its spaces this way, which is why its Size and Damping controls can reshape them, and Amp Rig designs its cabinets from a click, a short noise body and a few filters.

Any short sound works as a creative IR too: a single piano note, a cymbal swell, a reversed tail. Convolving a voice with a bell recording makes the voice ring at the bell's pitches. Designed IRs carry no one else's rights, so you can ship them freely.

Prepare the file

Whichever way you made it, clean the IR up in an audio editor before you use it:

  • Trim the start to just before the first sound arrives. Leave a gap only if you want built-in pre-delay; most effects, including Space Mini, have a Pre-Delay control for that.
  • Trim the end where the tail sinks into the noise, and fade out over the last 50 to 200 milliseconds so it does not stop abruptly.
  • Normalise so the loudest sample sits just below full scale. Effects level IRs in different ways, so an IR can still come out louder or quieter than the effect's own spaces; adjust the effect's level, not the file.
  • Remove DC offset if your editor offers it. A file that is not centred on zero thumps when it starts.
  • Export a WAV file.

What Maru accepts when an effect loads your IR file:

PropertyAccepted
FormatWAV only, up to 16 MiB
ChannelsMono, stereo, or four-channel true stereo, depending on the effect
Sample rate8 kHz to 384 kHz; the host converts it to the rate the effect runs at
LengthUp to the effect's own limit. Space Mini holds 6 seconds at 48 kHz (3 seconds at 96 kHz)
SamplesFinite values only

A file that is too long or has the wrong channel count is refused with a message rather than being cut short or folded down, so shorten it or export the channel layout the effect asks for.

Use your impulse response

You use your own IRs by building them into an effect. Maru's convolution effects, including Space Mini and Amp Rig, play their own designed IRs and don't take a file from their panels.

If you are building an effect, ship your IR inside it as a factory sound. A factory IR reaches your effect as its first channel only and at the file's own sample rate, so export it as mono at the rate your effect runs at, or design stereo IRs in code. Build a reverb, room or cabinet effect explains how to bind it to a selector.

Rights. An IR of a room you recorded is yours. An IR of someone else's venue, studio or product may need their permission to publish, and an IR you downloaded keeps its own licence: many free IR packs forbid redistribution inside another product. Note where each IR came from and under what terms.

If it doesn't sound right

What you hearLikely causeWhat to try
Hollow or phasey when mixed with the dry soundThe IR starts with a long gap, or the dry sound is doubled inside the IRTrim the start; lower the effect's mix
A hum or hiss under the tailBackground noise or mains hum in the recordingRe-record in a quieter moment, use a longer sweep, or trim the tail earlier and fade it
A chirp or click before the soundSpeaker distortion from the sweep, or a pre-echo before the direct soundTrim the start up to the direct sound
Thin, little bassCaptured with a click, or a small speakerUse a sweep and a full-range speaker, or add bass with EQ after the effect
The tail stops abruptlyThe file was cut without a fadeFade out the last 50 to 200 milliseconds
The stereo image is narrowThe IR is monoRecord two microphones, or design a stereo IR
The file is refusedToo long, too large, wrong channel count or not a WAVCheck it against the table above

Ask your agent

text
Read the Maru Help article "Make your own impulse response". I recorded a
sweep in my stairwell as a 48 kHz stereo WAV. Help me trim and fade the
recovered IR, then add it to my reverb module as a factory IR next to the
designed spaces, with its provenance recorded.

Developers can find the convolution building blocks and the IR preparation helpers in the DSP library.